在线留言| 联系我们| 收藏本站 欢迎光临无锡广和盛化工设备有限公司官方网站!
当前位置:行业新闻

不锈钢反应釜的气密性试验

发布日期:2019-09-19 04:41:07 访问次数:65

小易为你介绍一下不锈钢反应釜的气密性试验。

不锈钢反应釜的过程中,溢流保护装置在程度上有效地包括气缸,并且在设定过程中,液体排出口主要位于气缸的下侧,并且在设计过程中 工艺,在缸体上端面的中心位置处的对接接头,在缸体的上端表面处形成的空气出口孔,以及用于阻挡弹性垫圈的对接管道正下方的柱状浮体 对接管的下端口。


 不锈钢反应釜的静环端面在程度上可以具有0.05mm的垂直公差。 在操作过程中,该设备可用于液压试验,密封处的泄漏量不得超过10ml / h。弹簧不允许有生锈和变形等缺陷,总接触面积大于80%。不锈钢反应器机械密封的动环和静环表面不得有划痕,凹凸或划痕,接触面平整度应符合规定要求。


 不锈钢反应釜在程度上用作气密性试验。在旋转状态下,机械密封的油底壳不应产生连续的小气泡。目视检查填料密封的填料压盖是在末端还是单端。机器密封的油杯中是否有油,双端机械密封的润滑系统中的油是否足够,减速器中的油是否达到油窗的1/3,是否有油 每个润滑系统漏油。


 在不锈钢反应釜运行过程中,有效检查各连接管道上的阀门,管件,绝缘层和管道是否完好无损,操作过程中手动阀门的操作是否有效手轮是否完好,阀门是否关闭,阀门是否平稳打开和关闭,安全阀是否关闭,以及所需的实用程序是否准备就绪。

英文:

Xiaoyi will introduce the gas tightness test of stainless steel reactor for you.


In the process of stainless steel reactor, the overflow protection device effectively includes the cylinder to a certain extent, and in the setting process, the liquid outlet is mainly located at the lower side of the cylinder, and in the design process, the butt joint at the central position of the upper end face of the cylinder block, and the air outlet formed at the upper end surface of the cylinder block. The holes and the lower ports of the cylindrical floating butt pipe directly below the butt pipe for blocking the elastic washer.


The static ring end face of stainless steel reactor can have a vertical tolerance of 0.05 mm to a certain extent. During operation, the equipment can be used for hydraulic test, and the leakage at the seal can not exceed 10 ml/h. Spring is not allowed to have rust and deformation defects, the total contact area is more than 80%. There shall be no scratches, concave convex or scratches on the surfaces of the moving and static rings of the mechanical seals of stainless steel reactors, and the smoothness of the contact surface shall meet the requirements.


Stainless steel reactor is used for air tightness test to a certain extent. In the rotating state, the oil pan of mechanical seal should not produce continuous small bubbles. Visually check whether the packing gland of packing seal is at the end or at the single end. Whether there is oil in the oil cup sealed by the machine, whether there is enough oil in the lubrication system of the double-ended mechanical seal, whether the oil in the reducer reaches 1/3 of the oil window, whether there is oil leakage in each lubrication system.


During the operation of stainless steel reactor, check the valves, fittings, insulating layer and pipelines on the connecting pipes effectively, whether the manual valve is in good condition during operation, whether the valves are closed, whether the valves are opened and closed smoothly, whether the safety valves are closed or not, and the required facts. Is the program ready?

联系我们
服务热线

0510-85605893

传真号码0510-85600555

企业邮箱xngl@xngl.com

地址无锡惠山经济开发区堰新东路9号